Illuminating Polysulfide Distribution in Lithium Sulfur Batteries; Tracking Polysulfide Shuttle Using Operando Optical Fluorescence Microscopy.

High-energy-density lithium sulfur (Li-S) batteries suffer heavily from the polysulfide shuttle effect, a result of the dissolution and transport of intermediate polysulfides from the cathode, into the electrolyte, and onto the anode, leading to rapid cell degradation. If this primary mechanism of cell failure is to be overcome, the distribution, dynamics, and degree of polysulfide transport must first be understood in depth. In this work, operando optical fluorescence microscope imaging of optically accessible Li-S cells is shown to enable real-time qualitative visualization of the spatial distribution of lithium polysulfides, both within the electrolyte and porous cathode. Quantitative determinations of spatial concentration are also possible at a low enough concentration. The distribution throughout cycling is monitored, including direct observation of polysulfide shuttling to the anode and consequent dendrite formation. This was enabled through the optimization of a selective fluorescent dye, verified to fluoresce proportionally with concentration of polysulfides within Li-S cells. This ability to directly and conveniently track the spatial distribution of soluble polysulfide intermediates in Li-S battery electrolytes, while the cell operates, has the potential to have a widespread impact across the field, for example, by enabling the influence of a variety of polysulfide mitigation strategies to be assessed and optimized, including in this work the LiNO3 additive.

Isotopic biographies reveal horse rearing and trading networks in medieval London.

This paper reports a high-resolution isotopic study of medieval horse mobility, revealing their origins and in-life mobility both regionally and internationally. The animals were found in an unusual horse cemetery site found within the City of Westminster, London, England. Enamel strontium, oxygen, and carbon isotope analysis of 15 individuals provides information about likely place of birth, diet, and mobility during the first approximately 5 years of life. Results show that at least seven horses originated outside of Britain in relatively cold climates, potentially in Scandinavia or the Western Alps. Ancient DNA sexing data indicate no consistent sex-specific mobility patterning, although three of the five females came from exceptionally highly radiogenic regions. Another female with low mobility is suggested to be a sedentary broodmare. Our results provide direct and unprecedented evidence for a variety of horse movement and trading practices in the Middle Ages and highlight the importance of international trade in securing high-quality horses for medieval London elites.

The coax monopole antenna: A flexible end-fed antenna for ultrahigh field transmit/receive arrays.

PURPOSE: The coax monopole antenna is presented for body imaging at 7 T. The antenna is fed at one end, eliminating the possibility of cable-coil coupling and simplifying cable routing. Additionally, its flexibility improves loading to the subject. METHODS: Like the coax dipole antenna, an interruption in the shield of the coaxial cable allows the current to extend to the outside of the shield, generating a B1 + field. Matching is achieved using a single inductor at the distal side, and a cable trap enforces the desired antenna length. Finite difference time domain simulations are employed to optimize the design parameters. Phantom measurements are conducted to determine the antenna's B1 + efficiency and to find the S-parameters in straight and bent positions. Eight-channel simulations and measurements are performed for prostate imaging. RESULTS: The optimal configuration is a length of 360 mm with a gap position of 40 mm. Simulation data show higher B1 + levels for the coax monopole (20% in the prostate), albeit with a 5% lower specific absorbance rate efficiency, compared to the fractionated dipole antenna. The S11 of the coax monopole exhibits remarkable robustness to loading changes. In vivo prostate imaging demonstrates B1 + levels of 10-14 µT with an input power of 8 × 800 W, which is comparable to the fractionated dipole antenna. High-quality images and acceptable coupling levels were achieved. CONCLUSION: The coax monopole is a novel, flexible antenna for body imaging at 7 T. Its simple design incorporates a single inductor at the distal side to achieve matching, and one-sided feeding greatly simplifies cable routing.

Deep learning based correction of RF field induced inhomogeneities for T2w prostate imaging at 7 T.

At ultrahigh field strengths images of the body are hampered by B1 -field inhomogeneities. These present themselves as inhomogeneous signal intensity and contrast, which is regarded as a "bias field" to the ideal image. Current bias field correction methods, such as the N4 algorithm, assume a low frequency bias field, which is not sufficiently valid for T2w images at 7 T. In this work we propose a deep learning based bias field correction method to address this issue for T2w prostate images at 7 T. By combining simulated B1 -field distributions of a multi-transmit setup at 7 T with T2w prostate images at 1.5 T, we generated artificial 7 T images for which the homogeneous counterpart was available. Using these paired data, we trained a neural network to correct the bias field. We predicted either a homogeneous image (t-Image neural network) or the bias field (t-Biasf neural network). In addition, we experimented with the single-channel images of the receive array and the corresponding sum of magnitudes of this array as the input image. Testing was carried out on four datasets: the test split of the synthetic training dataset, volunteer and patient images at 7 T, and patient images at 3 T. For the test split, the performance was evaluated using the structural similarity index measure, Wasserstein distance, and root mean squared error. For all other test data, the features Homogeneity and Energy derived from the gray level co-occurrence matrix (GLCM) were used to quantify the improvement. For each test dataset, the proposed method was compared with the current gold standard: the N4 algorithm. Additionally, a questionnaire was filled out by two clinical experts to assess the homogeneity and contrast preservation of the 7 T datasets. All four proposed neural networks were able to substantially reduce the B1 -field induced inhomogeneities in T2w 7 T prostate images. By visual inspection, the images clearly look more homogeneous, which is confirmed by the increase in Homogeneity and Energy in the GLCM, and the questionnaire scores from two clinical experts. Occasionally, changes in contrast within the prostate were observed, although much less for the t-Biasf network than for the t-Image network. Further, results on the 3 T dataset demonstrate that the proposed learning based approach is on par with the N4 algorithm. The results demonstrate that the trained networks were capable of reducing the B1 -field induced inhomogeneities for prostate imaging at 7 T. The quantitative evaluation showed that all proposed learning based correction techniques outperformed the N4 algorithm. Of the investigated methods, the single-channel t-Biasf neural network proves most reliable for bias field correction.

Silicon-Based Solid-State Batteries: Electrochemistry and Mechanics to Guide Design and Operation.

Solid-state batteries (SSBs) are promising alternatives to the incumbent lithium-ion technology; however, they face a unique set of challenges that must be overcome to enable their widespread adoption. These challenges include solid-solid interfaces that are highly resistive, with slow kinetics, and a tendency to form interfacial voids causing diminished cycle life due to fracture and delamination. This modeling study probes the evolution of stresses at the solid electrolyte (SE) solid-solid interfaces, by linking the chemical and mechanical material properties to their electrochemical response, which can be used as a guide to optimize the design and manufacture of silicon (Si) based SSBs. A thin-film solid-state battery consisting of an amorphous Si negative electrode (NE) is studied, which exerts compressive stress on the SE, caused by the lithiation-induced expansion of the Si. By using a 2D chemo-mechanical model, continuum scale simulations are used to probe the effect of applied pressure and C-rate on the stress-strain response of the cell and their impacts on the overall cell capacity. A complex concentration gradient is generated within the Si electrode due to slow diffusion of Li through Si, which leads to localized strains. To reduce the interfacial stress and strain at 100% SOC, operation at moderate C-rates with low applied pressure is desirable. Alternatively, the mechanical properties of the SE could be tailored to optimize cell performance. To reduce Si stress, a SE with a moderate Young's modulus similar to that of lithium phosphorous oxynitride (∼77 GPa) with a low yield strength comparable to sulfides (∼0.67 GPa) should be selected. However, if the reduction in SE stress is of greater concern, then a compliant Young's modulus (∼29 GPa) with a moderate yield strength (1-3 GPa) should be targeted. This study emphasizes the need for SE material selection and the consideration of other cell components in order to optimize the performance of thin film solid-state batteries.

Simulation-based evaluation of SAR and flip angle homogeneity for five transmit head arrays at 14 T.

INTRODUCTION: Various research sites are pursuing 14 T MRI systems. However, both local SAR and RF transmit field inhomogeneity will increase. The aim of this simulation study is to investigate the trade-offs between peak local SAR and flip angle uniformity for five transmit coil array designs at 14 T in comparison to 7 T. METHODS: Investigated coil array designs are: 8 dipole antennas (8D), 16 dipole antennas (16D), 8 loop coils (8D), 16 loop coils (16L), 8 dipoles/8 loop coils (8D8L) and for reference 8 dipoles at 7 T. Both RF shimming and kT-points were investigated by plotting L-curves of peak SAR levels vs flip angle homogeneity. RESULTS: For RF shimming, the 16L array performs best. For kT-points, superior flip angle homogeneity is achieved at the expense of more power deposition, and the dipole arrays outperform the loop coil arrays. DISCUSSION AND CONCLUSION: For most arrays and regular imaging, the constraint on head SAR is reached before constraints on peak local SAR are violated. Furthermore, the different drive vectors in kT-points alleviate strong peaks in local SAR. Flip angle inhomogeneity can be alleviated by kT-points at the expense of larger power deposition. For kT-points, the dipole arrays seem to outperform loop coil arrays.

Engineering Solution-Processed Non-Crystalline Solid Electrolytes for Li Metal Batteries.

Non-crystalline Li-ion solid electrolytes (SEs), such as lithium phosphorus oxynitride, can uniquely enable high-rate solid-state battery operation over thousands of cycles in thin film form. However, they are typically produced by expensive and low throughput vacuum deposition, limiting their wide application and study. Here, we report non-crystalline SEs of composition Li-Al-P-O (LAPO) with ionic conductivities > 10-7 S cm-1 at room temperature made by spin coating from aqueous solutions and subsequent annealing in air. Homogenous, dense, flat layers can be synthesized with submicrometer thickness at temperatures as low as 230 °C. Control of the composition is shown to significantly affect the ionic conductivity, with increased Li and decreased P content being optimal, while higher annealing temperatures result in decreased ionic conductivity. Activation energy analysis reveals a Li-ion hopping barrier of ≈0.4 eV. Additionally, these SEs exhibit low room temperature electronic conductivity (< 10-11 S cm-1) and a moderate Young's modulus of ≈54 GPa, which may be beneficial in preventing Li dendrite formation. In contact with Li metal, LAPO is found to form a stable but high impedance passivation layer comprised of Al metal, Li-P, and Li-O species. These findings should be of value when engineering non-crystalline SEs for Li-metal batteries with high energy and power densities.

Multi-echo MR thermometry in the upper leg at 7 T using near-harmonic 2D reconstruction for initialization.

PURPOSE: The aim of this work is the development of a thermometry method to measure temperature increases in vivo, with a precision and accuracy sufficient for validation against thermal simulations. Such an MR thermometry model would be a valuable tool to get an indication on one of the major safety concerns in MR imaging: the tissue heating occurring due to radiofrequency (RF) exposure. To prevent excessive temperature rise, RF power deposition, expressed as specific absorption rate, cannot exceed predefined thresholds. Using these thresholds, MRI has demonstrated an extensive history of safe usage. Nevertheless, MR thermometry would be a valuable tool to address some of the unmet needs in the area of RF safety assessment, such as validation of specific absorption rate and thermal simulations, investigation of local peak temperatures during scanning, or temperature-based safety guidelines. METHODS: The harmonic initialized model-based multi-echo approach is proposed. The method combines a previously published model-based multi-echo water/fat separated approach with an also previously published near-harmonic 2D reconstruction method. The method is tested on the human thigh with a multi-transmit array at 7 T, in three volunteers, and for several RF shims. RESULTS: Precision and accuracy are improved considerably compared to a previous fat-referenced method (precision: 0.09 vs. 0.19°C). Comparison of measured temperature rise distributions to subject-specific simulated counterparts show good relative agreement for multiple RF shim settings. CONCLUSION: The high precision shows promising potential for validation purposes and other RF safety applications.

Marmoset core visual object recognition behavior is comparable to that of macaques and humans.

Among the smallest simian primates, the common marmoset offers promise as an experimentally tractable primate model for neuroscience with translational potential to humans. However, given its exceedingly small brain and body, the gap in perceptual and cognitive abilities between marmosets and humans requires study. Here, we performed a comparison of marmoset behavior to that of three other species in the domain of high-level vision. We first found that marmosets outperformed rats - a marmoset-sized rodent - on a simple recognition task, with marmosets robustly recognizing objects across views. On a more challenging invariant object recognition task used previously in humans, marmosets also achieved high performance. Notably, across hundreds of images, marmosets' image-by-image behavior was highly similar to that of humans - nearly as human-like as macaque behavior. Thus, core aspects of visual perception are conserved across monkeys and humans, and marmosets present salient behavioral advantages over other small model organisms for visual neuroscience.

Collagen-like Motifs of SasG: A Novel Fold for Protein Mechanical Strength.

The Staphylococcus aureus surface protein G (SasG) is associated with host colonisation and biofilm formation. As colonisation occurs at the liquid-substrate interface bacteria are subject to a myriad of external forces and, presumably as a consequence, SasG displays extreme mechanical strength. This mechanical phenotype arises from the B-domain; a repetitive region composed of alternating E and G5 subdomains. These subdomains have an unusual structure comprising collagen-like regions capped by triple-stranded ß-sheets. To identify the determinants of SasG mechanical strength, we characterised the mechanical phenotype and thermodynamic stability of 18 single substitution variants of a pseudo-wildtype protein. Visualising the mechanically-induced transition state at a residue-level by ϕ-value analysis reveals that the main force-bearing regions are the N- and C-terminal 'Mechanical Clamps' and their side-chain interactions. This is tailored by contacts at the pseudo-hydrophobic core interface. We also describe a novel mechanical motif - the collagen-like region and show that glycine to alanine substitutions, analogous to those found in Osteogenesis Imperfecta (brittle bone disease), result in a significantly reduced mechanical strength.

Tier-based formalism for safety assessment of custom-built radio-frequency transmit coils.

The purpose of this work is to propose a tier-based formalism for safety assessment of custom-built radio-frequency (RF) coils that balances validation effort with the effort put in determinating the safety factor. The formalism has three tier levels. Higher tiers require increased effort when validating electromagnetic simulation results but allow for less conservative safety factors. In addition, we propose a new method to calculate modeling uncertainty between simulations and measurements and a new method to propagate uncertainties in the simulation into a safety factor that minimizes the risk of underestimating the peak specific absorption rate (SAR). The new safety assessment procedure was completed for all tier levels for an eight-channel dipole array for prostate imaging at 7 T and an eight-channel dipole array for head imaging at 10.5 T, using data from two different research sites. For the 7 T body array, the validation procedure resulted in a modeling uncertainty of 77% between measured and simulated local SAR distributions. For a situation where RF shimming is performed on the prostate, average power limits of 2.4 and 4.5 W/channel were found for tiers 2 and 3, respectively. When the worst-case peak SAR among all phase settings was calculated, power limits of 1.4 and 2.7 W/channel were found for tiers 2 and 3, respectively. For the 10.5 T head array, a modeling uncertainty of 21% was found based on B1 + mapping. For the tier 2 validation, a power limit of 2.6 W/channel was calculated. The demonstrated tier system provides a strategy for evaluating modeling inaccuracy, allowing for the rapid translation of novel coil designs with conservative safety factors and the implementation of less conservative safety factors for frequently used coil arrays at the expense of increased validation effort.

A Mathematical Model of Aqueous Humor Production and Composition.

Purpose: We develop a mathematical model that predicts aqueous humor (AH) production rate by the ciliary processes and aqueous composition in the posterior chamber (PC), with the aim of estimating how the aqueous production rate depends on the controlling parameters and how it can be manipulated. Methods: We propose a compartmental mathematical model that considers the stromal region, ciliary epithelium, and PC. All domains contain an aqueous solution with different chemical species. We impose the concentration of all species on the stromal side and exploit the various ion channels present on the cell membrane to compute the water flux produced by osmosis, the solute concentrations in the AH and the transepithelial potential difference. Results: With a feasible set of parameters, the model predictions of water flux from the stroma to the PC and of the solute concentrations in the AH are in good agreement with measurements. Key parameters which impact the aqueous production rate are identified. A relevant role is predicted to be played by cell membrane permeability to \(\text{K}^+\) and \(\text{Cl}^-\), by the level of transport due to the Na+-H+ exchanger and to the co-transporter of Na+/K+/2Cl-; and by carbonic anhydrase. Conclusions: The mathematical model predicts the formation and composition of AH, based on the structure of the ciliary epithelium. The model provides insight into the physical processes underlying the functioning of drugs that are adopted to regulate the aqueous production. It also suggests ion channels and cell membrane properties that may be targeted to manipulate the aqueous production rate.

Synthesis and Evaluation of Pseudomonas aeruginosa ATP Synthase Inhibitors.

New antibiotics with unique biological targets are desperately needed to combat the growing number of resistant bacterial pathogens. ATP synthase, a critical protein found in all life, has recently become a target of interest for antibiotic development due to the success of the anti-tuberculosis drug bedaquiline, and while many groups have worked on developing drugs to target bacterial ATP synthase, few have been successful at inhibiting Pseudomonas aeruginosa (PA) ATP synthase specifically. PA is one of the leading causes of resistant nosocomial infections across the world and is extremely challenging to treat due to its various antibiotic resistance mechanisms for most commonly used antibiotics. Herein, we detail the synthesis and evaluation of a series of C1/C2 quinoline analogues for their ability to inhibit PA ATP synthase and act as antibiotics against wild-type PA. From this survey, we found six compounds capable of inhibiting PA ATP synthase in vitro showing that bulky/hydrophobic C1/C2 substitutions are preferred. The strongest inhibitor showed an IC50 of 10 µg/mL and decreased activity of PA ATP synthase to 24% relative to the control. While none of the compounds were able to inhibit wild-type PA in cell culture, two showed improved inhibition of PA growth when permeability of the outer membrane was increased or efflux was knocked out, thus demonstrating that these compounds could be further developed into efficacious antibiotics.

Complex Natural Products Derived from Pyrogallols.

Pyrogallols (1,2,3-trihydroxybenzenes) are abundant in Nature, easily oxidized, and are central precursors to important natural products. The rich chemistry of their oxidized derivatives, the hydroxy-o-quinones, has been studied for over a century and still attracts the interest of the scientific community. Only in the last ten years have critical insights of pyrogallol chemistry from the mid-twentieth century been applied to modern natural product synthesis. Historical studies of pyrogallol chemistry, including [5+2], [4+2], and formal [5+5] cycloadditions are discussed here and reactivity guidelines established. The application and remarkable selectivity of these cycloadditions is then showcased in the recent syntheses of several fungal natural products, including dibefurin, epicolactone, the merocytochalasans, and preuisolactone A. The authors hope that this contribution will spark further interest in the fascinating chemistry of pyrogallols and natural products derived from them.

Brain-like functional specialization emerges spontaneously in deep neural networks.

The human brain contains multiple regions with distinct, often highly specialized functions, from recognizing faces to understanding language to thinking about what others are thinking. However, it remains unclear why the cortex exhibits this high degree of functional specialization in the first place. Here, we consider the case of face perception using artificial neural networks to test the hypothesis that functional segregation of face recognition in the brain reflects a computational optimization for the broader problem of visual recognition of faces and other visual categories. We find that networks trained on object recognition perform poorly on face recognition and vice versa and that networks optimized for both tasks spontaneously segregate themselves into separate systems for faces and objects. We then show functional segregation to varying degrees for other visual categories, revealing a widespread tendency for optimization (without built-in task-specific inductive biases) to lead to functional specialization in machines and, we conjecture, also brains.

A perturbation approach for ultrafast calculation of RF field enhancements near medical implants in MRI.

Patients with medical implants often are deprived of magnetic resonance imaging examination because of safety risks. One specific risk is the enhancement of the radiofrequency fields around the medical implant potentially resulting in significant tissue heating and damage. The assessment of this enhancement is a computationally demanding task, with simulations taking hours or days to converge. Conventionally the source of the radiofrequency fields, patient anatomy, and the medical implant are simulated concurrently. To alleviate the computational burden, we reformulate a fast simulation method that views the medical implant as a small perturbation of the simulation domain without the medical implant and calculates the radiofrequency fields associated with this perturbation. Previously, this method required an extensive offline stage where the result is intractable for large simulation domains. Currently, this offline stage is no longer required and the method is completely online. The proposed method results in comparable radiofrequency fields but is orders of magnitude faster compared to standard simulation technique; the finite-difference time-domain, the finite-sums, and the finite element methods. This acceleration could enable patient-specific and potentially online radiofrequency safety assessment.

Performance and automation of ancient DNA capture with RNA hyRAD probes.

DNA hybridization-capture techniques allow researchers to focus their sequencing efforts on preselected genomic regions. This feature is especially useful when analysing ancient DNA (aDNA) extracts, which are often dominated by exogenous environmental sources. Here, we assessed, for the first time, the performance of hyRAD as an inexpensive and design-free alternative to commercial capture protocols to obtain authentic aDNA data from osseous remains. HyRAD relies on double enzymatic restriction of fresh DNA extracts to produce RNA probes that cover only a fraction of the genome and can serve as baits for capturing homologous fragments from aDNA libraries. We found that this approach could retrieve sequence data from horse remains coming from a range of preservation environments, including beyond radiocarbon range, yielding up to 146.5-fold on-target enrichment for aDNA extracts showing extremely low endogenous content (<1%). Performance was, however, more limited for those samples already characterized by good DNA preservation (>20%-30%), while the fraction of endogenous reads mapping on- and off-target was relatively insensitive to the original endogenous DNA content. Procedures based on two instead of a single round of capture increased on-target coverage up to 3.6-fold. Additionally, we used methylation-sensitive restriction enzymes to produce probes targeting hypomethylated regions, which improved data quality by reducing post-mortem DNA damage and mapping within multicopy regions. Finally, we developed a fully automated hyRAD protocol utilizing inexpensive robotic platforms to facilitate capture processing. Overall, our work establishes hyRAD as a cost-effective strategy to recover a set of shared orthologous variants across multiple ancient samples.

The Coax Dipole: A fully flexible coaxial cable dipole antenna with flattened current distribution for body imaging at 7 Tesla.

PURPOSE: The coax dipole antenna, a flexible antenna for body imaging at 7T is presented. Similar to the high impedance coil, this coaxial cable antenna is fed on the central conductor and through gaps in the shield, the current passes to the outside of the antenna to generate B1 field. This could achieve more favorable current distributions and better adaptation to the body curvature. METHODS: Finite difference time domain (FDTD) simulations are performed to optimize the positions of the gaps in the shield for a flat current profile. Lumped inductors are added to each end to reduce losses. The performance of a single antenna is compared to a fractionated dipole using B1 maps and MR thermometry. Finally, an array of eight coax dipoles is evaluated in simulations and used for in-vivo scanning. RESULTS: An optimal configuration is found with gaps located at 10 cm from the center and inductor values of 28 nH. In comparison to the fractionated dipole antenna, in single antenna phantom measurements the coax dipole achieves similar B1 amplitude with 18% lower peak temperature. In simulations, the eight-channel array of coax dipoles improved B1 homogeneity by 18%, along with small improvements in transmit efficiency and specific absorption rate (SAR). MRI measurements on three volunteers show more consistent performance for the coax dipoles. CONCLUSION: The coax dipole is a novel antenna design with a flattened current distribution resulting in beneficial properties. Also, the flexible design of the coax dipoles allows better adaptation to the body curvature and can potentially be used for a wide range of imaging targets.

Ultralow Thermal Conductivity, Multiband Electronic Structure and High Thermoelectric Figure of Merit in TlCuSe.

The entanglement of lattice thermal conductivity, electrical conductivity, and Seebeck coefficient complicates the process of optimizing thermoelectric performance in most thermoelectric materials. Semiconductors with ultralow lattice thermal conductivities and high power factors at the same time are scarce but fundamentally interesting and practically important for energy conversion. Herein, an intrinsic p-type semiconductor TlCuSe that has an intrinsically ultralow thermal conductivity (0.25 W m-1 K-1 ), a high power factor (11.6 µW cm-1 K-2 ), and a high figure of merit, ZT (1.9) at 643 K is described. The weak chemical bonds, originating from the filled antibonding orbitals p-d* within the edge-sharing CuSe4 tetrahedra and long TlSe bonds in the PbClF-type structure, in conjunction with the large atomic mass of Tl lead to an ultralow sound velocity. Strong anharmonicity, coming from Tl+ lone-pair electrons, boosts phonon-phonon scattering rates and further suppresses lattice thermal conductivity. The multiband character of the valence band structure contributing to power factor enhancement benefits from the lone-pair electrons of Tl+ as well, which modify the orbital character of the valence bands, and pushes the valence band maximum off the Γ-point, increasing the band degeneracy. The results provide new insight on the rational design of thermoelectric materials.

A two-dimensional type I superionic conductor.

Superionic conductors possess liquid-like ionic diffusivity in the solid state, finding wide applicability from electrolytes in energy storage to materials for thermoelectric energy conversion. Type I superionic conductors (for example, AgI, Ag2Se and so on) are defined by a first-order transition to the superionic state and have so far been found exclusively in three-dimensional crystal structures. Here, we reveal a two-dimensional type I superionic conductor, α-KAg3Se2, by scattering techniques and complementary simulations. Quasi-elastic neutron scattering and ab initio molecular dynamics simulations confirm that the superionic Ag+ ions are confined to subnanometre sheets, with the simulated local structure validated by experimental X-ray powder pair-distribution-function analysis. Finally, we demonstrate that the phase transition temperature can be controlled by chemical substitution of the alkali metal ions that compose the immobile charge-balancing layers. Our work thus extends the known classes of superionic conductors and will facilitate the design of new materials with tailored ionic conductivities and phase transitions.